Airworthiness Directive · Amendment 39-22036 · Time limits/maintenance checks
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2023-13-10. Comply with the one in force.
This AD applies to Airbus SAS Model airplanes specified in paragraphs (c)(1) through (4) of this AD, certificated in any category, with an original airworthiness certificate or original export certificate of airworthiness issued on or before November 10, 2020.
(1) Model A318-111, -112, -121, and -122 airplanes.
(2) Model A319-111, -112, -113, -114, -115, -131, -132, -133, -151N, and -153N airplanes.
(3) Model A320-211, -212, -214, -216, -231, -232, -233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes.
(4) Model A321-111, -112, -131, -211, -212, -213, -231, -232, -251N, -251NX, -252N, -252NX, -253N, -253NX, -271N, -271NX, -272N, and -272NX airplanes.
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A318 series; A319-111, -112, -113, -114, -115, -131, -132, -133, -151N, and -153N; A320 series; and A321 series airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0140, dated June 14, 2021 (EASA AD 2021-0140).
(1) Where EASA AD 2021-0140 refers to its effective date, this AD requires using the effective date of this AD.
(2) The provisions specified in paragraphs (1) and (2) of EASA AD 2021-0140 do not apply to this AD.
(3) Paragraph (3) of EASA AD 2021-0140 specifies revising “the approved [aircraft maintenance program] AMP” within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD.
(4) The initial compliance time for doing the tasks specified in paragraph (3) of EASA AD 2021-0140 is at the applicable “thresholds” as incorporated by the requirements of paragraph (3) of EASA AD 2021-0140, or within 90 days after the effective date of this AD, whichever occurs later.
(5) The provisions specified in paragraph (4) of EASA AD 2021-0140 do not apply to this AD.
(6) The “Remarks” section of EASA AD 2021-0140 does not apply to this AD.
After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals are allowed unless they are approved as specified in the provisions of the “Ref. Publications” section of EASA AD 2021-0140.
Accomplishing the actions required by this AD, including incorporating Task 531135-03-1 as required by EASA AD 2021-0140 and incorporated by reference in this AD, terminates Task 531135-01-2, as required by EASA AD 2020-0036R1 and incorporated by reference in AD 2020-20-05, and as required by paragraph (i) of AD 2020-20-05.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (l) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (k)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
