Airworthiness Directive · Amendment 39-21929 · Equipment/furnishings
Airbus SAS Airplanes
Superseded. A later AD replaced this one: AD 2023-07-02. Comply with the one in force.
This AD applies to all Airbus SAS airplanes, certificated in any category, as identified in paragraphs (c)(1) through (8) of this AD.
(1) Model A330-201, -202, -203, -223, and -243 airplanes.
(2) Model A330-301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes.
(3) Model A330-841 airplanes.
(4) Model A330-941 airplanes.
(5) Model A340-211, -212, and -213 airplanes.
(6) Model A340-311, -312, and -313 airplanes.
(7) Model A340-541 airplanes.
(8) Model A340-642 airplanes.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200, -300, -800, and -900 series airplanes; and Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by reports that the instructions on the doghouse door lock placard are unclear and incomplete. This AD requires replacing the placard with an improved instruction placard, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0136, dated June 4, 2021 (EASA AD 2021-0136).
(1) Where EASA AD 2021-0136 refers to its effective date, this AD requires using the effective date of this AD.
(2) Although EASA AD 2021-0136 specifies to “remove the placard and install an improved handling instructions placard on each affected part,” this AD requires replacing the placard on each affected part with an improved handling instructions placard.
(3) The “Remarks” section of EASA AD 2021-0136 does not apply to this AD.
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
