Airworthiness Directive · Amendment 39-19426 · Time limits/maintenance checks
Dassault Aviation Airplanes
Superseded. A later AD replaced this one: AD 2020-02-21. Comply with the one in force.
This AD applies to all Dassault Aviation Model FALCON 2000 airplanes, certificated in any category, all serial numbers.
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 2000 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Within 90 days after the effective date of this AD, revise the maintenance or inspection program, as applicable, to incorporate the information specified in Chapter 5-40, Airworthiness Limitations, DGT 113876, Revision 19, dated November 2017, of the Dassault Falcon 2000 Maintenance Manual. The initial compliance times for doing the tasks are at the time specified in Chapter 5-40, Airworthiness Limitations, DGT 113876, Revision 19, dated November 2017, of the Dassault Falcon 2000 Maintenance Manual, or within 90 days after the effective date of this AD, whichever occurs later; except as required by paragraphs (g)(1) through (g)(3) of this AD. The term “LDG” in the “First Inspection” column of any table in Chapter 5-40, Airworthiness Limitations, DGT 113876, Revision 19, dated November 2017, of the Dassault Falcon 2000 Maintenance Manual, means total airplane landings. The term “FH” in the “First Inspection” column of any table in Chapter 5-40, Airworthiness Limitations, DGT 113876, Revision 19, dated November 2017, of the Dassault Falcon 2000 Maintenance Manual, means total flight hours. The term “FC” in the “First Inspection” column of any table in Chapter 5-40, Airworthiness Limitations, DGT 113876, Revision 19, dated November 2017, of the Dassault Falcon 2000 Maintenance Manual, means total flight cycles.
(1) For Task 30-11-09-350-801 identified in the service information specified in the introductory text of paragraph (g) of this AD, the initial compliance time is the later of the times specified in paragraphs (g)(1)(i) and (g)(1)(ii) of this AD.
(i) At the earlier of the times specified in paragraphs (g)(1)(i)(A) and (g)(1)(i)(B) of this AD.
(A) Prior to the accumulation of 2,400 total flight hours or 2,000 total flight cycles, whichever occurs first.
(B) Within 2,400 flight hours or 2,000 flight cycles after April 7, 2014 (the effective date of AD 2014-03-12), whichever occurs first.
(ii) Within 30 days after April 7, 2014 (the effective date of AD 2014-03-12).
(2) For Task 52-20-00-610-801-01 identified in the service information specified in the introductory text of paragraph (g) of this AD, the initial compliance time is within 24 months after April 7, 2014 (the effective date of AD 2014-03-12).
(3) The limited service life of part number F2MA721512100 is 3,750 total flight cycles on the part or 6 years since the manufacturing date of the part, whichever occurs first.
After the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections), or intervals, may be used unless the actions, or intervals, are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD.
(1) Accomplishing the actions required by this AD terminates all of the requirements of AD 2014-03-12.
(2) Accomplishing the actions required by paragraph (g) of this AD terminates the requirements of paragraph (g) of AD 2010-26-05 for all Dassault Aviation Model FALCON 2000 airplanes.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
Aircraft
