Airworthiness Directive · Amendment 39-18792 · Main rotor control
Airbus Helicopters Deutschland GmbH (Previously Eurocopter Deutschland GmbH) Helicopters
This AD applies to the following helicopters, certificated in any category:
(1) Model EC135 P1, P2, P2+, T1, T2, and T2+ helicopters, serial number (S/N) 0005 through 00829, with a tail rotor control lever, part number (P/N) L672M2802205 or L672M1012212; cyclic control lever, P/N L671M1005250; collective control lever assembly, P/N L671M2020108; or collective control plate, P/N L671M5040207; installed; and
(2) Model MBB-BK 117 C-2 helicopters,S/N 9004 through 9310, with a tail rotor control lever assembly, P/N B672M1007101 or B672M1807101; tail rotor control lever, P/N B672M1002202 or L672M2802205; or lateral control lever assembly, P/N B670M1008101, installed.
We are superseding airworthiness directive (AD) 2014-05-06 for Eurocopter Deutschland GmbH (ECD) (now Airbus Helicopters Deutschland GmbH) Model EC135 and MBB-BK 117 C-2 helicopters to correct an error in the compliance time. AD 2014-05-06 required inspecting the flight- control bearings and installing bushings and washers. This AD requires the same actions. These actions are intended to prevent an unsafe condition on these products.
You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time.
(1) For Model EC135 P1, P2, P2+, T1, T2, and T2+ helicopters:
(i) Within the next 100 hours time-in-service (TIS) or at the next annual inspection, whichever occurs first, modify the left-hand (LH) and right-hand (RH) guidance units and the cyclic shaft by installing bushings and washers to prevent shifting of the bearings in the axial direction as follows:
(A) Remove and disassemble the LH guidance unit and install a bushing, P/N L672M1012260, between the bearing block and the lever of the LH guidance unit as depicted in Detail A of Figure 5 of Eurocopter Alert Service Bulletin EC135-67A-019, Revision 3, dated December 16, 2009 (EC135 ASB).
(B) For helicopters without a yaw brake, remove and disassemble the RH guidance unit and install a bushing, P/N L672M1012260, between the bearing block and the lever as depicted in Detail B of Figure 5 of EC135 ASB.=
(C) Remove and disassemble the cyclic shaft and install a washer, P/N L671M1005260, between the bearing block and the lever as depicted in Detail C of Figure 6 of EC135 ASB.
(D) Remove the collective control rod from the bellcrank and install a washer, P/N L221M1042208, on each side of the collective control rod and bellcrank as depicted in Detail D of Figure 6 of EC135 ASB.
(E) At intervals not to exceed 800 hours TIS or 36 months, whichever occurs first, inspect the bearings in the LH guidance unit, RH guidance unit, cyclic control, upper guidance unit, and linear voltage differential transducer plate for play. If any bearing is loose, replace the affected bearing with an airworthy bearing.
(2) For Model MBB-BK 117 C-2 helicopters:
(i) Within the next 100 hours TIS or at the next annual inspection, whichever occurs first, modify the LH and RH guidance units and the lateral control lever by installing bushings and washers to prevent shifting of the bearings in the axial direction as follows:
(A) Remove and disassemble the RH guidance unit and install a bushing, P/N L672M1012260, between the lever and the bracket as depicted in Detail B of Figure 4 of Eurocopter Alert Service Bulletin MBB BK117 C-2-67A-010, Revision 3, dated February 8, 2010 (BK117 ASB). Remove and disassemble the LH guidance unit and install a bushing, P/N L672M1012260, between the lever and the bracket as depicted in Detail C of Figure 4 of BK117 ASB.
(B) Remove the lateral control lever and install new bushings in accordance with the Accomplishment Instructions, paragraphs 3.C(9)(a) through 3.C(9)(g), of BK 117 ASB.
(C) Identify the modified lever assembly by writing “MBB BK117 C-2-67A-010” on the lever with permanent marking pen and protect with a single layer of lacquer (CM 421or equivalent).
(D) Apply corrosion preventive paste (CM 518 or equivalent) on the shank of the screws and install airworthy parts as depicted in Figure 5 of BK117 ASB.
(E) At intervals not to exceed 600 hours TIS or 24 months, whichever occurs first, inspect the bearings in the RH guidance unit, LH guidance unit, and lateral control guidance unit for play. If any bearing is loose, replace the affected bearing with an airworthy bearing.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
