AD 2016-23-09

You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time.

(1) Within 25 hours time-in-service (TIS) or 2 weeks, whichever occurs first, and thereafter at intervals not to exceed 25 hours TIS or 2 weeks, whichever occurs first, clean the upper and lower exposed surfaces of each M/R blade from an area starting at the butt end of the blade to three inches outboard of the doublers. Using a 3X or higher power magnifying glass and a light, inspect as follows:

(i) Visually inspect the exposed area of the lower grip pad and upper and lower grip plates of each M/R blade for a crack and any corrosion.

(ii) On the upper and lower exposed surfaces of each M/R blade from blade stations 24.5 to 35 for the entire chord width, visually inspect each layered doubler and blade skin for a crack and any corrosion. Pay particular attention for any cracking in a doubler or skin near or at the same blade station as the blade retention bolt hole (blade station 28).

(iii) Visually inspect the exposed areas of each bond line at the edges of the lower grip pad, upper and lower grip plates, and each layered doubler (bond lines) on the upper and lower surfaces of each M/R blade for the entire length and chord width for an edge void, any corrosion, loose or damaged adhesive squeeze-out, and an edge delamination. Pay particular attention to any crack in the paint finish that follows the outline of a grip pad, grip plate, or doubler, and to any loose or damaged adhesive squeeze-out, as these may be the indication of an edge void.

(2) If there is a crack, any corrosion, an edge void, loose or damaged adhesive squeeze-out, or an edge delamination during any inspection in paragraph (e)(1) of this AD, before further flight, do the following:

(i) If there is a crack in a grip pad or any grip plate or doubler, replace the M/R blade with an airworthy M/R blade.

(ii) If there is a crack in the M/R blade skin that is within maximum repair damage limits, repair the M/R blade. If the crack exceeds maximum repair damage limits, replace the M/R blade with an airworthy M/R blade.

(iii) If there is any corrosion within maximum repair damage limits, repair the M/R blade. If the corrosion exceeds maximum repair damage limits, replace the M/R blade with an airworthy M/R blade.

(iv) If there is an edge void in the grip pad or in a grip plate or doubler, determine the length and depth using a feeler gauge. Repair the M/R blade if the edge void is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade.

(v) If there is an edge void in a grip plate or doubler near the outboard tip, tap inspect the affected area to determine the size and shape of the void. Repair the M/R blade if the edge void is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade.

(vi) If there is any loose or damaged adhesive squeeze-out along any of the bond lines, trim or scrape away the adhesive without damaging the adjacent surfaces or parent material of the M/R blade. Determine if there is an edge void or any corrosion by lightly sanding the trimmed area smooth using 280 or finer grit paper. If there is no edge void or corrosion, refinish the sanded area.

(vii) If there is an edge delamination along any of the bond lines or a crack in the paint finish, determine if there is an edge void or a crack in the grip pad, grip plate, doubler, or skin by removing paint from the affected area by lightly sanding in a span-wise direction using 180-220 grit paper. If there are no edge voids and no cracks, refinish the sanded area.

(viii) If any parent material is removed during any sanding or trimming in paragraphs (e)(2)(vi) or (e)(2)(vii) of this AD, repair the M/R blade if the damage is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade.