Airworthiness Directive · Amendment 39-18113 · Periodic inspections
Bombardier, Inc. Airplanes
Superseded. A later AD replaced this one: AD 2021-07-03. Comply with the one in force.
This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, certificated in any category, serial numbers 7003 and subsequent.
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by reports of cracking on the skin panels and skin splice joints and angles at certain stringers at various locations between certain fuselage stations. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or revised maintenance requirements and airworthiness limitations, and incorporating structural repairs and modifications to preclude widespread fatigue damage (WFD). We are issuing this AD to detect and correct WFD, which could adversely affect the structural integrity of the airplane.
Within 60 days after the effective date of this AD: Revise the maintenance or inspection program, as applicable, by incorporating the airworthiness limitations (AWL) tasks specified in paragraphs (g)(1) through (g)(4) of this AD. The initial compliance times for the tasks start from the applicable threshold times specified in Part 2 Airworthiness Requirements, Revision 9, dated June 10, 2013, of Appendix B, Airworthiness Limitations, of Bombardier CL-600-2B19, Maintenance Requirements Manual, CSP A-053; except that, for airplanes that have accumulated more than 38,000 total flight cycles as of the effective date of this AD, the initial compliance time for the AWL tasks is before the accumulation of 2,000 flight cycles after the effective date of this AD.
(1) AWL Task 53-41-109, Longitudinal Str. 6 splice at STR 6 and 20, of Appendix B, Airworthiness Limitations, of Part 2, Airworthiness Requirements, Revision 9, dated June 10, 2013, of the Bombardier CL-600-2B19, Maintenance Requirements Manual, CSP A-053.
(2) AWL Task 53-41-110, Longitudinal Str. 6 splice butt strap at Str. 6, FS409.0 to FS617.0, of Appendix B, Airworthiness Limitations, of Part 2, Airworthiness Requirements, Revision 9, dated June 10, 2013, of the Bombardier CL-600-2B19, Maintenance Requirements Manual, CSP A-053.
(3) AWL Task 53-41-204, Frame splice angles at STR 6 and 20, of Appendix B, Airworthiness Limitations, of Part 2, Airworthiness Requirements, Revision 9, dated June 10, 2013, of the Bombardier CL-600-2B19, Maintenance Requirements Manual, CSP A-053.
(4) AWL Task 53-41-205, Longitudinal skin splice at STR 6 and 20., of Appendix B, Airworthiness Limitations, of Part 2, Airworthiness Requirements, Revision 9, dated June 10, 2013, of the Bombardier CL-600-2B19, Maintenance Requirements Manual, CSP A-053.
After the maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections) or intervals may be used unless the actions or intervals are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (j)(1) of this AD.
Before the accumulation of 60,000 total flight cycles: Install repairs and modifications to preclude widespread fatigue damage at locations specified in the tasks identified in paragraphs (g)(1) through (g)(4) of this AD, using a method approved by the Manager, New York ACO, ANE-170, FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature.
