Airworthiness Directive · Amendment 39-15952 · Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 Turboshaft Engines
Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 Turboshaft Engines
Superseded. A later AD replaced this one: AD 2009-26-07. Comply with the one in force.
This AD applies to Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines if modified by Turbomeca Modification TU332 and fitted with modules M05 as listed by serial number in Figure 1 of Turbomeca S.A. Mandatory Service Bulletin (MSB) No. A292 72 0825, Version A, dated May 27, 2009. These engines are installed on, but not limited to, Eurocopter France AS350B, AS350BA, AS365N, AS350B1, AS350B2, Eurocopter Deutschland GmbH MBB-BK117-C1, Agusta A109K2, and Sikorsky S-76A+, S-76A++ and S-76C helicopters.
This document publishes in the Federal Register an amendment adopting emergency airworthiness directive (AD) 2009-12-51 that was sent previously to all known U.S. owners and operators of Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires initial and repetitive visual inspections of certain reduction gearboxes (module M05) for oil leakage, repair if leaking, and repair of all affected modules as terminating action to the repetitive inspections. This AD results from reports of oil leaks from certain reduction gearbox (module M05) front casings. The engine manufacturer reported that the lubrication duct plug was not properly bonded/glued in place. We are issuing this AD to prevent uncommanded in-flight engine shutdown, possible engine fire, and an emergency autorotation landing.
You are responsible for having the actions required by this AD performed within the compliance times specified unless the actions have already been done.
Before further flight:
(1) Visually inspect the module M05 lubrication duct for oil leakage. Use paragraph 1.C.(1)(a), paragraph 2.A., and Figure 2 of Turbomeca S.A. MSB No. A292 72 0825, Version A, dated May 27, 2009, to do the inspection.
(2) If oil leakage is found, repair the module M05 lubrication duct. Use paragraph 2.B.1, Figure 3, and Figure 4 in Turbomeca S.A. MSB No. A292 72 0825, Version A, dated May 27, 2009, to do the repair.
If no oil leakage is found, repeat the visual inspection every four flight hours, or after the last flight of each day, whichever comes first.
(h) The actions required by paragraph (g) of this AD may be performed by the owner/operator holding at least a private pilot certificate, and must be entered into the aircraft records showing compliance with this AD in accordance with 14 CFR 43.9 and 14 CFR 91.417(a)(2)(v).
(i) As optional terminating action to the repetitive visual inspections in paragraph (g) of this AD, repair the affected modules M05 as specified in paragraph (f)(2) of this AD.
The aircraft, engines and makers this AD names, by the model designations in its text. A model listed here may still be outside the AD's serial ranges.
