Airworthiness Directive · Amendment 39-15435 · McDonnell Douglas Model DC-8-55, DC-8F-54, and DC-8F-55 Airplanes; and Model DC-8-60, DC-8-70, DC-8-60F, and DC-8-70F Series Airplanes
McDonnell Douglas Model DC-8-55, DC-8F-54, and DC-8F-55 Airplanes; and Model DC-8-60, DC-8-70, DC-8-60F, and DC-8-70F Series Airplanes
This AD applies to McDonnell Douglas Model DC-8-55, DC-8F-54, DC-8F-55, DC-8-61, DC-8-62, DC-8-63, DC-8-61F, DC-8-62F, DC-8-63F, DC-8-71, DC-8-72, DC-8-73, DC-8-71F, DC-8-72F, and DC-8-73F airplanes, certificated in any category; as identified in Boeing Alert Service Bulletin DC8-53A080, dated June 22, 2004.
The FAA is superseding an existing airworthiness directive (AD) that applies to certain McDonnell Douglas Model DC-8-55, DC-8F-54, and DC-8F-55 airplanes; and Model DC-8-60, DC-8-70, DC-8-60F, and DC-8- 70F series airplanes. The existing AD currently requires a one-time inspection for previous repairs of the aft fuselage skin panel at the longeron 28 skin splice, repetitive inspections for cracks of the same area, and related investigative and corrective actions. The existing AD also provides optional actions for extending the repetitive inspection intervals. This new AD re-defines and more clearly describes the optional actions for extending the repetitive inspection intervals. This AD results from our determination that the inspections and actions described in the existing AD do not adequately address the unsafe condition. We are issuing this AD to detect and correct cracks in the aft fuselage skin at the longeron 28 skin splice, which could lead to loss of structural integrity of the aft fuselage, resulting in rapid decompression of the airplane.
You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
For all airplanes: At the applicable time in paragraph (f)(1) or (f)(2) of this AD, do a general visual inspection to determine if there are previous repairs of the aft fuselage skin panel at the longeron 28 skin splice; in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin DC8-53A080, dated June 22, 2004. Then do the applicable actions specified in paragraphs (g) and (h) of this AD.
(1) For airplanes that have accumulated fewer than 24,000 total flight cycles as of February 28, 2007 (the effective date of AD 2007-02-02): Within 24 months after February 28, 2007, or prior to accumulating 24,000 total flight cycles, whichever occurs later.
(2) For airplanes that have accumulated 24,000 total flight cycles or more as of February 28, 2007: Within 12 months after February 28, 2007.
Note 1: For the purposes of this AD, a general visual inspection is: “A visual examination of an interior or exterior area, installation, or assembly to detect obvious damage, failure, or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight, or droplight and may require removal or opening of access panels or doors. Stands, ladders, or platforms may be required to gain proximity to the area being checked.”
For areas that do not have a previous repair: Before further flight after the initial inspection in paragraph (f) of this AD, do general visual and high-frequency eddy current (HFEC) inspections for discrepancies at longeron 28 between the bolted connection of the tail section to forward of the flat aft pressure bulkhead, on both the left and right sides, and do all applicable related investigative and corrective actions before further flight. Do all actions in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin DC8-53A080, dated June 22, 2004. Repeat the general visual and HFEC inspections thereafter at intervals not to exceed 2,000 flight cycles until an optional action in paragraph (i) of this AD is accomplished.
For areas that have a previous repair: Within 24 months after accomplishing the initial inspection in paragraph (f) of this AD, remove the previous repair(s), and install a local repair, in accordance with Boeing DC-8 Service Rework Drawing SR08530032, dated January 13, 2004, including Boeing Parts List PL SR08530032, dated January 7, 2004, Boeing Advance Engineering Order, Advanced Drawing Change A, dated April 1, 2004, and Boeing Engineering Order, dated January 13, 2004. Do the inspections in paragraph (j) of this AD thereafter at the applicable interval specified in paragraph (j)(1) or (j)(2) of this AD.
(i) Installing a full-length preventive modification, doing a full-length repair, or doing a local repair, in accordance with Boeing DC-8 Service Rework Drawing SR08530032, dated January 13, 2004, including Boeing Parts List PL SR08530032, dated January 7, 2004; Boeing Advance Engineering Order, Advanced Drawing Change A, dated April 1, 2004; and Boeing Engineering Order, dated January 13, 2004; ends the repetitive inspection intervals specified in paragraph (g) of this AD.
After removing the previous repair(s) and doing the actions specified in paragraph (h) of this AD or doing any optional repair or modification described in paragraph (i) of this AD: Do the actions described in paragraph (j)(1) or (j)(2) of this AD as applicable, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin DC8-53A080, dated June 22, 2004. If any discrepancy is discovered during any inspection required by this paragraph, before further flight, repair the discrepancy using a method approved in accordance with the procedures specified in paragraph (l) of this AD.
(1) For areas that have been repaired on airplanes that do have internal finger doublers installed: Within 30,000 flight cycles after doing the optional repair or modification, do a general visual inspection for discrepancies along all four external edges of the doublers. Repeat the inspection thereafter at intervals not to exceed 5,000 flight cycles.
(2) For areas that have been repaired on airplanes that do not have internal finger doublers installed: Do the actions specified in paragraph (j)(2)(i) or (j)(2)(ii) of this AD, as applicable.
(i) For any repair that is 12 inches or less along the longeron: Within 15,000 flight cycles after removing the previous repair(s) and doing the actions specified in paragraph (h) of this AD or doing any optional repair or modification specified in paragraph (i) of this AD, do a general visual inspection for discrepancies along all four external edges of the doublers. Repeat the general visual inspection thereafter at intervals not to exceed 5,000 flight cycles.
(ii) For any repair that is greater than 12 inches in length along the longeron: Within 15,000 flight cycles after removing the previous repair(s) and doing the actions specified in paragraph (h) of this AD or doing any optional repair or modification specified in paragraph (i) of this AD, do a low-frequency eddy current (LFEC) inspection for discrepancies along all four external edges of the doublers. Repeat the LFEC inspection thereafter at intervals not to exceed 10,000 flight cycles.
Submit a report of positive findings of the inspections required by paragraphs (g) and (j) of this AD to Boeing Commercial Airplanes, Manager, Structure/Payloads, Technical and Fleet Support, Service Engineering/Commercial Aviation Services, Long Beach Division, 3855 Lakewood Boulevard, Long Beach, California 90846, at the applicable time specified in paragraph (k)(1) or (k)(2) of this AD. The report must include the inspection results, a description of any discrepancies found, the airplane fuselage number, and the total number of landings and flight hours on the airplane. Information collection requirements contained in this AD have been approved by the Office of Management and Budget (OMB) under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.) and have been assigned OMB Control Number 2120-0056.
(1) For any inspection accomplished after the effective date of this AD: Submit the report within 30 days after performing the inspection.
(2) For any inspection accomplished prior to the effective date of this AD: Submit the report within 30 days after the effective date of this AD.
