Airworthiness Directive · Amendment 39-12041 · Boeing Model 737-100, -200, and -200C Series Airplanes
Boeing Model 737-100, -200, and -200C Series Airplanes
Superseded. A later AD replaced this one: AD 2013-09-02. Comply with the one in force.
Model 737-100, -200, and -200C series airplanes; on which the left- or right-hand inboard flap tracks of the wing outboard flap have a part number (P/N) listed in Table 1 (below) of this AD; certificated in any category.
| Name | Part Number |
|---|---|
| Boeing | 65-46428-9 |
| 65-46428-15 | |
| 65-46428-17 | |
| 65-46428-19 | |
| 65-46428-21 | |
| 65-46428-23 | |
| 65-46428-25 | |
| 65-46428-27 | |
| 65-46428-33 | |
| 65-46428-35 |
Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance per paragraph (c) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.
This amendment adopts a new airworthiness directive (AD) that is applicable to certain Boeing Model 737-100, -200, and -200C series airplanes. This action requires repetitive inspections of the aft end of each inboard flap track of the wing outboard flap, and corrective actions, if necessary. This action is necessary to detect and correct damage of the aft end of each flap track, which could result in loss of the outboard trailing edge flap and consequent loss of controllability of the airplane.
To detect and correct damage of the aft end of each inboard flap track of the wing outboard flap, which could result in loss of the outboard trailing edge flap and consequent loss of controllability of the airplane, accomplish the following:
(a) Do a detailed visual inspection to detect damage (corrosion, cracking) of the aft end of the left- and right-hand inboard flap tracks of the wing outboard flap, per Boeing All Operator Message (AOM) M-7200-00-01854, dated July 27, 2000; at the latest of the times specified in paragraphs (a)(1), (a)(2), and (a)(3) of this AD. Repeat the inspection thereafter at intervals not to exceed 1,200 flight cycles.
Note 2: For the purposes of this AD, a detailed visual inspection is defined as: “An intensive visual examination of a specific structural area, system, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at intensity deemed appropriate by the inspector. Inspection aids such as mirror, magnifying lenses, etc., may be used. Surface cleaning and elaborate access procedures may be required.”
(1) Within 30 days after the effective date of this AD.
(2) Within 1,200 flight cycles after the last documented inspection or overhaul of the aft end of each flap track.
(3) Before the accumulation of 15,000 total flight cycles.
(b) If any damage (corrosion, cracking) is detected, before further flight, repair or rework the flap track per the “Repair and Rework Instructions” specified in Boeing AOM M-7200-00-01854, dated July 27, 2000. Where the AOM specifies that the manufacturer may be contacted for disposition of certain corrective actions (i.e., repair and/or rework of the flaps), this AD requires such repair and/or rework to be done per a method approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA; or per data meeting the type certification basis of the airplane approved by a Boeing Company designated engineering representative (DER) who has been authorized by the Manager, Seattle ACO, to make such findings. For a repair method to be approved by the Manager, Seattle ACO, as required by this paragraph, the Manager's approval letter must specifically reference this AD.
