# AD 2026-22-13: Lycoming Engines

> The FAA is superseding Airworthiness Directive (AD) 2026-17- 10, which applied to Lycoming Engines (Lycoming) Model O-235, O-540, and IO-540 engines with a certain piston pin installed. AD 2026-17-10 required replacement of the affected piston pin with a part eligible for installation and, for certain engines, oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates. AD 2026-17-10 also prohibited the installation of an affected piston pin on any engine. Since the FAA issued AD 2026-17-10, the manufacturer has identified additional Lycoming Model engines that are subject to the unsafe condition, and the FAA determined the need to clarify the definition for an "affected piston pin," and include corrective action for engine models that were not listed in the manufacturer's service material. This AD requires replacement of the affected piston pin with a part eligible for installation and, for certain engines, oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates. This AD also prohibits the installation of an affected piston pin on any engine. This AD also expands the applicability to include additional affected engines with a certain piston pin installed. The FAA is issuing this AD to address the unsafe condition on these products.

Page: https://www.aerscheduler.com/airworthiness-directives/2026-22-13
Maker: Lycoming Engines
Product: Engine
Published: November 9, 2026
Effective: November 24, 2026
Amendment: 39-23515
Supersedes: 2026-17-10

## At a glance

Quoted from the FAA's summary of this AD. The full text below is what applies.

- What it requires: This AD requires replacement of the affected piston pin with a part eligible for installation and, for certain engines, oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates. This AD also prohibits the installation of an affected piston pin on any engine.
- Why: The FAA is issuing this AD to prevent failure of the piston pin.
- Check an aircraft by N-number: https://www.aerscheduler.com/airworthiness-directives/check

## Applies to

This AD applies to Lycoming Engines (Lycoming) Model engines identified in table 1 to paragraph (c) of this AD with an installed piston pin having part number (P/N) LW-13445 that was manufactured between January 7, 2021 to December 15, 2025. If the date of manufacture for the piston pin cannot be determined, this AD is applicable. If the current piston pins (P/N LW-13445) were installed prior to January 7, 2021, this AD is not applicable.

**Table 1 to Paragraph (c)—Lycoming Model Engines**
| Engine series | Engine model |
| --- | --- |
| O-235 | -C1, -C1A, -C1B, -C1C, -C2A, -C2B, -C2C, -E1, -E1B, -E2A, -E2B, -F1, -F1B, -F2A, -F2B, -G1, -G1B, -G2A, -G2B, -H2C, -J2A, -J2B, -K2A, -K2B, -K2C, -L2A, -L2C, -M1, -M2C, -M3C, -N2A, -N2C, -P1, -P2A, -P2C, -P3C. |
| O-320 | -A1A, -A1B, -A2A, -A2B, -A2C, -A2D, -A3A, -A3B, -A3C, -B1A, -B1B, -B2A, -B2B, -B2C, -B2D, -B2E, -B3A, -B3B, -B3C, -D1A, -D1B, -D1C, -D1D, -D1F, -D2A, -D2B, -D2C, -D2F, -D2J, -D3G, -E1A, -E1B, -E1C, -E1F, -E1J, -E2A, -E2B, -E2C, -E2D, -E2F, -E2G, -E2H, -E3D, -E3H. |
| IO-320 | -B1A, -B1C, -B1D, -B1E, -B2A, -C1A,-C1B, -D1A, -D1B, -D1C, -E1A, -E1B, -E2A,-E2B. |
| AIO-320 | -A1B, -B1B, -C1B. |
| LIO-320 | -B1A, -C1A. |
| AEIO-320 | -D1B, -D2B, -E1A, -E1B, -E2A, -E2B. |
| VO-435 | -A1A (O-435-21), -A1B (O-435-6), -A1C (O-435-23, -23A, -23B, -23C), -A1D (O-435-6A), -A1E, -A1F, -B1A. |
| TVO-435 | -A1A, -B1A (O-435-25A), -B1B, -C1A, -D1A, -D1B, -E1A, -F1A, -G1A, -G1B. |
| O-540 | -J1A5D, -J1B5D, -J1C5D, -J1D5D, -J2A5D, -J2B5D, -J2C5D, -J2D5D, -J3A5, -J3A5D, -J3C5D, -L3C5D. |
| IO-540 | -AB1A5, -J4A5, -W1A5, -W1A5D, -W3A5D. |

## What it requires

### Definitions

  (1) For the purpose of this AD, a “part eligible for installation” is one of the following:

    (i) A piston pin that does not have P/N LW-13445.

    (ii) A piston pin having P/N LW-13445 that was not manufactured between January 7, 2021 to December 15, 2025.

  (2) For the purpose of this AD, an “affected piston pin” is a piston pin having P/N LW-13445 and one of the following:

    (i) A date of manufacture between January 7, 2021 to December 15, 2025.

    (ii) A date of manufacture that is unknown.

  (3) For the purpose of this AD, Group 1 engines are all affected engines, except engines with an installed piston pin having P/N LW-13445 with a manufacture date between March 23, 2023 to December 15, 2025, or an installed piston pin having P/N LW-13445 with a manufacture date that is unknown.

  (4) For the purpose of this AD, Group 2 engines are engines with an installed piston pin having P/N LW-13445 with a manufacture date between March 23, 2023 to December 15, 2025, or an installed piston pin having P/N LW-13445 with a manufacture date that is unknown.

### Required Actions

  (1) For Group 1 and Group 2 engines, except for Group 2 engines with greater than or equal to 150 hours time in service (TIS) as of the effective date of this AD, within 5 hours TIS after the effective date of this AD, perform an oil change and visual inspection of the engine oil filter, oil pressure screen, and oil suction screen for metal particulates.

> Note 1 to paragraph (h)(1): Guidance for engine oil filter, oil pressure screen, and oil suction screen inspection instructions and identification of metallic solids may be found in Lycoming Mandatory Service Bulletin No. (MSB) No. 480F, dated May 25, 2017.

  (2) If any metal particulates are found during the oil change and inspection required by paragraph (h)(1) of this AD, before further flight, replace any affected piston pin with a part eligible for installation in accordance with the Required Action of Lycoming MSB 667A, dated March 12, 2026 (Lycoming MSB 667A), as applicable to engine model.

  (3) For Group 1 engines with an installed piston pin with a manufacture date between January 07, 2021, to March 22, 2023, where metal particulates were not found during the oil change and inspection required by paragraph (h)(1) of this AD, at the next maintenance event requiring the removal of a cylinder assembly with an affected piston pin, or at the next engine overhaul not to exceed the time between overhaul specified in Lycoming Service Instruction No. 1009BF, dated July 20, 2026, whichever occurs first after the effective date of this AD, replace any affected piston pin with a part eligible for installation in accordance with the Required Action of Lycoming MSB 667A, as applicable to engine model.

  (4) For Group 2 engines with greater than or equal to 150 hours TIS as of the effective date of this AD, before further flight, replace any affected piston pin with a part eligible for installation in accordance with the Required Action of Lycoming MSB 667A, as applicable to engine model.

  (5) For Group 2 engines with less than 150 hours TIS as of the effective date of this AD, within 25 hours TIS after the effective date of this AD but before or upon reaching 150 total hours TIS since installation of the affected piston pins, whichever comes first after the effective date of this AD, replace any affected piston pin with a part eligible for installation in accordance with the Required Action of Lycoming MSB 667A, as applicable to engine model.

### Installation Prohibition

After the effective date of this AD, do not install an affected piston pin as defined in paragraph (g)(2) of this AD on any engine.

### No Return of Parts

Although the service material specifies returning certain parts to the manufacturer, this AD does not include those requirements.

## Filed under

- [Lycoming](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming)
- [Lycoming O-320](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-o-320)
- [Lycoming IO-540](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-io-540)
- [Lycoming O-235](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-o-235)
- [Lycoming O-540](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-o-540)
- [Lycoming IO-320](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-io-320)
- [Lycoming O-435](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-o-435)
- [Lycoming VO-435](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-vo-435)
- [Lycoming TVO-435](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-tvo-435)
- [Lycoming AEIO-320](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-aeio-320)
- [Lycoming LYCOMING](https://www.aerscheduler.com/airworthiness-directives/engines/lycoming-lycoming)

## Source

- The Federal Register document 2026-22785, the legal text: https://www.federalregister.gov/documents/2026/11/09/2026-22785/airworthiness-directives-lycoming-engines
- Current status and corrections: the FAA's Dynamic Regulatory System, https://drs.faa.gov/

_Not the official record. Whether an AD applies to one aircraft depends on its serial number, installed equipment and records, and is a certificated mechanic's determination._
