# AD 2026-22-11: Airbus SAS Airplanes

> The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 airplanes. This AD was prompted by a report of a missing main landing gear (MLG) brake rod center pin nut sub-assembly detected during an inspection. This AD requires, depending on airplane configuration, inspection of the MLG brake rod center pin nut, lock ring, and end plate, inspection of the MLG brake rod center pin and nut, and applicable corrective actions. This AD also requires additional work for certain airplanes. The FAA is issuing this AD to address the unsafe condition on these products.

Page: https://www.aerscheduler.com/airworthiness-directives/2026-22-11
Maker: Airbus SAS
Product: Airplane
Published: November 10, 2026
Effective: December 15, 2026
Amendment: 39-23513
Supersedes: nothing

## At a glance

Quoted from the FAA's summary of this AD. The full text below is what applies.

- What it requires: This AD requires, depending on airplane configuration, inspection of the MLG brake rod center pin nut, lock ring, and end plate, inspection of the MLG brake rod center pin and nut, and applicable corrective actions. This AD also requires additional work for certain airplanes.
- Why: The FAA is issuing this AD to address discrepancies of the MLG brake rod center pin and nut that could lead to detachment of the MLG brake rod center pin nut sub-assembly.
- Applies to: certain Airbus SAS Model A350-941 airplanes
- Check an aircraft by N-number: https://www.aerscheduler.com/airworthiness-directives/check

## Applies to

This AD applies to Airbus SAS Model A350-941 airplanes, certificated in any category, as identified in European Union Aviation Safety Agency (EASA) AD 2025-0150, dated July 14, 2025 (EASA AD 2025-0150).

## What it requires

### Requirements

Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 2025-0150.

### Exceptions to EASA AD 2025-0150

  (1) Where EASA AD 2025-0150 refers to its effective date, this AD requires using the effective date of this AD.

  (2) Where EASA AD 2025-0150 refers to May 9, 2025 (the effective date of EASA AD 2025-0095), this AD requires using the effective date of this AD.

  (3) This AD does not adopt the “Remarks” section of EASA AD 2025-0150.

  (4) Where the material referenced in EASA AD 2025-0150 specifies “Subtask 321162-40100060004”, this AD requires replacing that text with “Subtask 321162-40100060004 or the Subtask applicable to your airplane configuration”.

### Additional AD Provisions

The following provisions also apply to this AD:

  (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (j) of this AD and email to: AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

  (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR-520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

  (3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any material referenced in EASA AD 2025-0150 contains paragraphs that are labeled as RC, the instructions in RC paragraphs, including subparagraphs under an RC paragraph, must be done to comply with this AD; any paragraphs, including subparagraphs under those paragraphs, that are not identified as RC are recommended. The instructions in paragraphs, including subparagraphs under those paragraphs, not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the instructions identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to instructions identified as RC require approval of an AMOC.

### Additional Information

For more information about this AD, contact Andrew Younglove, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-231-3644; email: andrew.e.younglove@faa.gov.

## Filed under

- [Airbus](https://www.aerscheduler.com/airworthiness-directives/aircraft/airbus)
- [Airbus A350-941](https://www.aerscheduler.com/airworthiness-directives/aircraft/airbus-a350-941)

## Source

- The Federal Register document 2026-22897, the legal text: https://www.federalregister.gov/documents/2026/11/10/2026-22897/airworthiness-directives-airbus-sas-airplanes
- Current status and corrections: the FAA's Dynamic Regulatory System, https://drs.faa.gov/

_Not the official record. Whether an AD applies to one aircraft depends on its serial number, installed equipment and records, and is a certificated mechanic's determination._
