# AD 2026-22-06: Diamond Aircraft Industries Inc. Airplanes

> The FAA is adopting a new airworthiness directive (AD) for all Diamond Aircraft Industries Inc. (DAI) Model DA 40, DA 40 F, and DA 40 NG airplanes. This AD was prompted by several reports of passenger door separation during flight. This AD requires revising the existing airplane flight manual (AFM) to provide the flight crew with revised operating limitations, emergency procedures, and normal operating procedures; inspecting the passenger door latching mechanism and safety hook mechanism areas and performing corrective action, as applicable; inspecting the safety hook, latching bolts, front and rear door guide blocks, canopy and passenger door warning light, carbon hinges, tension spring, retaining block, safety hook push button, latching mechanism spring, gas spring, and door frame; measuring the passenger door handle actuation force; modifying the airplane with placards; replacing the gas spring; and replacing the hook assembly, retaining block, door guide blocks, and door sealant if necessary. The FAA is issuing this AD to address the unsafe condition on these products.

Page: https://www.aerscheduler.com/airworthiness-directives/2026-22-06
Maker: Diamond Aircraft Industries Inc.
Product: Airplane
Published: November 2, 2026
Effective: December 7, 2026
Amendment: 39-23508
Supersedes: nothing

## At a glance

Quoted from the FAA's summary of this AD. The full text below is what applies.

- What it requires: This AD requires revising the existing airplane flight manual (AFM) to provide the flight crew with revised operating limitations, emergency procedures, and normal operating procedures; inspecting the passenger door latching mechanism and safety hook mechanism areas and performing corrective action, as applicable; inspecting the safety hook, latching bolts, front and rear door guide blocks, canopy and passenger door warning light, carbon hinges, tension spring, retaining block, safety hook push button, latching mechanism spring, gas spring, and door frame; measuring the passenger door handle actuation force; modifying the airplane with placards; replacing the gas spring; and replacing the hook assembly, retaining block, door guide blocks, and door sealant if necessary.
- Applies to: all Diamond Aircraft Industries Inc. (DAI) Model DA 40, DA 40 F, and DA 40 NG airplanes
- Repeats: its required actions mention a repeat inspection or replacement
- Check an aircraft by N-number: https://www.aerscheduler.com/airworthiness-directives/check

## Applies to

This AD applies to all Diamond Aircraft Industries Inc. (DAI) Model DA 40, DA 40 F, and DA 40 NG airplanes, certificated in any category.

## What it requires

### Required Actions

  (1) Within 100 hours time-in-service (TIS) or 100 days, whichever occurs first after the effective date of this AD, revise the existing AFM for the airplane to include the information specified in the applicable AFM temporary revision specified in paragraphs (g)(1) through (3) of this AD.

    (i) The owner/operator (pilot) holding at least a private pilot certificate may revise the existing AFM for the airplane and must enter compliance with the applicable paragraph of this AD into the airplane maintenance records in accordance with 14 CFR 43.9(a) and 91.417(a)(2)(v). The record must be maintained as required by 14 CFR 91.417, 121.380, or 135.439.

    (ii) The AFM revision required by paragraph (i)(1) of this AD may be accomplished before the initial inspection and modification required by paragraph (i)(2) or (3) of this AD for that airplane.

  (2) For airplanes with less than 100 total hours TIS as of the effective date of this AD: Within 100 hours TIS or 100 days, whichever occurs first after the effective date of this AD, accomplish the initial inspection of the safety hook, latching bolts, front and rear door guide blocks and the modification of the airplane with placards in accordance with the instructions of Section III, steps 5, 20 through 23, 28, 30, 31, and 33 through 36 in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD, except accomplish the actions required by step 20(f) in accordance with paragraphs (i)(4) and (5) of this AD.

  (3) For airplanes that have accumulated 100 or more total hours TIS as of the effective date of this AD: Within 100 hours TIS or 100 days, whichever occurs first after the effective date of this AD, accomplish the initial inspection of the canopy and passenger door warning light, carbon hinges, safety hook, tension spring, retaining block, safety hook push button, safety hook mechanism, latching mechanism spring, gas spring, latching bolts, front and rear door guide blocks, and door frame; measure the passenger door handle actuation force; and accomplish the modification of the airplane with placards in accordance with the instructions of Section III, steps 2 through 10, 12, 13, 15, 17, 18, 20 through 24, and 28 through 36 in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD, except accomplish the actions required by step 20(f) in accordance with paragraphs (i)(4) and (5) of this AD.

  (4) If, during the inspection required by step 20(f) in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD, the force measured is less than 1.8 kg (18 N), and if the force measured during the inspection required by step 20(c) was between 2 kg (20 N) and 6 kg (60 N), perform the following:

    (i) Repeat the inspection required by step 20(c) in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD every 100 hours TIS until the replacement of the gas spring required by paragraph (i)(4)(ii) of this AD is accomplished.

    (ii) Within 12 months after the effective date of this AD, replace the gas spring in accordance with the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD.

  (5) If, during the inspection specified in step 20(f) in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD, the force measured is less than 1.8 kg (18 N), and if the force measured during the inspection required by step 20(c) was greater than 6 kg (60 N) or less than 2 kg (20 N), before further flight, replace the gas spring.

  (6) If, during any inspection as required by paragraph (i)(2) or (3) of this AD, any findings, as defined in Section III, steps 5, 6, 9, 12, 20, and 23 are identified, before further flight, accomplish the applicable corrective action(s) in accordance with the instructions of Section IV, IV.1, steps 1 through 9, VI.2 [ sic ], steps 1 and 2, VI.3 [ sic ], steps 1 and 2, and VI.4 [ sic ], steps 1 through 5 in the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD.

  (7) Where the instructions of Section III or Section IV of the Diamond Aircraft Work Instruction specified in paragraph (f) of this AD state to contact the manufacturer “in case of doubt” or for approved instructions, this AD requires before further flight, using instructions approved by the Manager, International Validation Branch, FAA; Transport Canada; or DAI's Transport Canada Design Organization Approval (DOA), and within the compliance time specified therein, accomplishing those instructions. If approved by the DOA, the approval must include the DOA-authorized signature.

### No Reporting Requirement

Although the material referenced in paragraph (f) of this AD specifies to submit information to the manufacturer, this AD does not require that action.

## Filed under

- [Diamond](https://www.aerscheduler.com/airworthiness-directives/aircraft/diamond)
- [Diamond DA 40](https://www.aerscheduler.com/airworthiness-directives/aircraft/diamond-da-40)

## Source

- The Federal Register document 2026-22310, the legal text: https://www.federalregister.gov/documents/2026/11/02/2026-22310/airworthiness-directives-diamond-aircraft-industries-inc-airplanes
- Current status and corrections: the FAA's Dynamic Regulatory System, https://drs.faa.gov/

_Not the official record. Whether an AD applies to one aircraft depends on its serial number, installed equipment and records, and is a certificated mechanic's determination._
